Archive

Category Archives for "Kitchen Tips"

4 Easy Steps to Tighten a Loose Moen Single Hand Kitchen Faucet

4 Easy Steps to Tighten a Loose Moen Single Hand Kitchen Faucet

At some point, your kitchen faucet will need repair or replacement. Parts inside the kitchen faucet wear out or accumulate sediment. This affects performance and ultimately requires attention.

While some faucets have lasted for decades, others may need to be replaced in a few years. Whether it is for cosmetics or performance, this job is something that the average owner will find within its reach.

A loose Moen single hand kitchen faucet 

There are times that you will always find that your kitchen faucet is loose. The more it is on use and operating, at times it becomes weak, or even some screws or nuts loosen. You will experience leaks, and that means you might be unable to turn it off or on completely.

Why should you tighten a loose kitchen faucet handle? 

A loose kitchen faucet handle can be annoying. You may not be able to control the water flow, and they will eventually leak.

The best thing to do if you have a loose kitchen faucet handle is to fix it as soon as possible. You will only need a screwdriver most of the time. Sometimes a new pin (available at any hardware store) is in order. Either way, it's a solution that can be done in less than an hour.

In this guide, we will learn how to tighten a loose Moen single hand kitchen faucet. With a more serious issue, however, it is advised to contact professionals.

Also Read: ​How to Remove Flow Restrictor from Grohe Kitchen Faucet​​​

Requirements & Steps

These are some of the basic tools you will need when you are tightening your Moen single hand kitchen faucet. The tools include:

  • Masking tape
  • Screwdriver
  • A pair of pliers
  • A towel
  • Teflon plumber tape

You should always have them lined up before you start your work. Having to look for every tool in the middle of your working process might lead to frustrations and confusion.

These tools will make your work easy and save you time fixing your loose Moen kitchen faucet. You might also need a manual that will help you if you need to disassemble the handle or the faucet altogether.

This might sound drastic, but that is what you will need to do by carefully following what is written on your manual, and the process is simple.

1. Setup for repair work

  • Check for any leaks 

You should first determine if any leaks are occurring from the faucet. You might find that the faucet is just loose with no leaks and you just need to tighten it. If it is not leaking, it doesn't mean you leave it without repairing it as it might soon start leaking, the earlier, the better.

  • Water supply

First, start by turning off the water supply before doing anything else. You can check under your sink and turn the valves you see in a clockwise direction to stop the water from flowing into the faucet. First, you will need to remove any object that might block you from reaching the valves. They are designed differently, and that means if you notice there are no valves, you can turn the main water line. But with Moen faucets, you will note there are valves.

  • Remove any water from the faucet 

Once you are sure the water line is off, you can turn the faucet on to relieve the water pressure. If there is water that had gone into the faucet, it will flow out. You should allow this for about 2 minutes as it will stop indicating that no more water inside the faucet.

2. Remove the valves 

You should remove the valves using your pair of pliers so that you can determine what needs to be done. They are normally tight, and you cannot do it with your hands, and that is why you need the help of a pair of pliers. You can now proceed and start fixing your Moen single hand kitchen faucet.

3. Fixing the loose Faucet

You should cover the holes of the sink using its sink strainer to avoid losing some important parts into the holes. If you do not have one, you can take a towel or old cloth and use it to cover the holes of the sink.

4. Examine the faucet handle 

Keenly examine the faucet handle to note where the setscrew has a recessed hex head at the handle or caps on top of the handle. You will use a screwdriver or al wrench at this point. You need to turn the tool you are using to go into the setscrew and turn it until you feel it's tight.

  • Apply masking tape 

Carefully lift the handle if you are unable to reach the setscrew if it's down. You will now use your masking tape by applying it on the area around the cups of the faucet handle and that is only when you do not find hex-head setscrew on the faucet handle. Make sure the masking tape doesn't overlap the edges of the cap.

  • Tightening the handle 

Use the tip of your screwdriver to remove the cap gently from the faucet handle. Now tighten the setscrew located under the cap by turning it in a clockwise direction to tighten the handle. You should remove the cap and tighten the screw and if possible replace the cup and lastly remove the masking tape from the top of the handle.

You can open the water supply for water to run into the faucet and check if it's still loose. If it's loose it will wiggle around when you touch it, but if it's tight, you will be able to feel it while opening it. You will feel more comfortable when you use a tight Moen single hand kitchen faucet than using a loose one.

Instead of using straps to tie around your faucets handle, just tighten it following the given instructions. You can easily get back your faucet operating well when you take the project into action. Your Moen faucet will work efficiently when you do the simple steps to tighten it.

Vital Aspects to Remember

When you finish and realize that tightening the faucets doesn't work, then it might be the stem inside the handle that is worn out. You should be keen because many are made of plastic. But you can still tighten it without having to purchase a new one.

You can take your the worn-out stem and use a Teflon pipe thread tape to wrap it tightly. Now slip the handle back over the stem to put it back in place. One single wrap is enough to create a snug fit. Once you have done that you can now proceed to tighten your faucet now that the worn-out stem is stable.

Some faucets operate even if the handle it's loose, but the experience is not comfortable, and soon you will start getting leaks. You should never leave it that way as water will continue running making your bill go up.

May Like: ​How to Tighten Garbage Disposal Blades: Useful Tips​​​

You need to act, and that means you need to fix it by tightening the hand kitchen faucet. It is normal to feel frustrated or disappointed when your kitchen faucet is not working properly.

Final thoughts 

Remember that all Moen faucets have cartridge valves, and if the faucet is leaking, you will have to replace the cartridge. Possibly, you can also replace the O-rings to stop the leakage from occurring. The cartridge found in Moen is always smaller and simply made compared to others. These are usually made using plastic, and that is why it is easier to deal with them.

Anytime you want to replace the cartridge because it is faulty, you will have to stick to the same faucet model so that you make sure you order the correct parts of the Moen. Tightening the loose faucet is simple if you follow the highlighted instructions.

How to Remove Flow Restrictor from Grohe Kitchen Faucet

How to Remove Flow Restrictor from Grohe Kitchen Faucet

Since the mid-1990s, water flow restrictors have been integrated into kitchen faucets as a way to conserve water. The Grohe restrictor for kitchen faucets is a flow limiter connected to the end of the spout. So if you’re noticing a decreasing water pressure, you might want to remove the limiter.

You need to finish doing your chores like washing utensils but the pressure at which the water flowing is very low. The flow of water may affect the proper cleaning of your appliances, and that might make you annoyed.

May Like: ​10 Simple Tips to Fix a Scratched Kitchen Cabinet​​​

You might think that your connection has a problem and want to call a plumber to identify the problem, only for your friend to tell you it's something you can do by yourself. Your friend tells you it's a flow restrictor that you can remove on your own to increase the pressure. You might have heard that for the first time, and that means you need to read about it and why it's there before you go on removing it.

What does a water flow limiter on Grohe do?

First, you need to understand that a water flow restrictor is put in place to save water. Water is an important or a precious resource, and that is why almost all government legislations always put a restrictor on faucets. You can only increase the flow once you remove the flow restrictor as its part of the aerator connected to the end of the faucet spout.

How to remove flow restrictor from Grohe kitchen faucet 

You can do this using some common household items in your house. That means you do not need a plumber or any professional personnel to remove the flow restrictor for you. It is not time-consuming as you may think as you can manage to do this within 10 to 15 minutes. This article will provide information on how to remove the flow restrictor from Grohe kitchen faucet.

Requirements

These are some of the essential items you need to have to go about the whole process. You should have:

  • Joint pliers
  • Painters tape

You might need rubber gloves or even screwdrivers. However, these should be your back-up options in case the need arises.

You will also need a manual if you need to go back to the instruction to remove the aerator. When you follow the instructions carefully, you will manage the process in the shortest time possible. You will carry out your duties feeling much comfortable as you don't have a limitation on your Grohe kitchen faucet.

Locating the Aerator

The manual you have perhaps has a diagram and you might identify where the aerator is and how it looks like. You first need to locate the aerator at the end of the faucet spout to identify where they connect. You will know it's an aerator as it is located at the tip or head of the faucet. It has a mesh screen that can direct the water into the sink.

The aerator is responsible for reducing the volume of water that flows from your faucet and also reduces splashing in sinks. That is why the flow of your water is on the low. Many individuals always end up saving money and also water. You will not pay a high bill of water if your aerator is working properly and is put in place. Most people who pay a low bill, have always reduced their monthly water usage, thus lowering their utility bills.

You will have to remove the aerator, and that means you will have to regulate how you use the water. You do not have to feel guilty that you will have to increase the pressure flow of your water because you can still save water. Do this by carefully checking how you use water and closing it whenever it's not in use.

But it is not advisable to remove your aerator for good as you will need to return it.

Once you spot where the aerator is, take your painters' tape and wrap several layers around the aerator. You need to do that to protect the finish from the pliers when you are removing it. The painters' tape is the best to use as it doesn't leave any residue or glue on it. When you finally remove the painters' tape, you will find it easier as it will not stick on the aerator.

Removing Grohe Flow Restrictor

You will first have to close the sink drain. Alternatively, you can choose to wrap it with a piece of cloth to block parts from going through the drain.

While removing the aerator, you will have to grab it between the jaws with the help of your joint pliers.

It is always recommended to wrap a cloth around the aerator so that it cannot have marks from the grip from the pliers. Doing that will leave your aerator looking new with no marks or any bruises formed on it.

Turn in a counterclockwise direction until you feel it is loose and you can remove it by your hand. You should understand that if your Grohe kitchen faucet is new, then it will be hard to grasp them with your fingers because they fit into the spout. That is why having a rubber glove is sometimes necessary as it can be of great help.

When using the pliers, you need to hold it firmly so that it doesn't slip and hit you. Some aerators can be removed with hand, and that is by turning it clockwise without the help of a tool.

Make sure when you are removing the aerator, you only grab the aerator not the end of the spout. You might end up damaging it, and it will be a double work and also expensive.

Disassemble the aerator on the counter then remove the small plastic disc with the holes in it.

Arrange the aerator parts in order on the countertop once you have removed the aerator. Now you will have successfully removed the flow restrictor from your Grohe kitchen faucet.

Cleaning the aerator 

You can turn on the water gently and wash the faucet flow restrictor as well as the faucet aerator screen. You need to be diligent when turning on the water as it will come with a lot of pressure from the faucet, and that means you need to turn it on slowly.

You can use your fingertips to clean any dirt on the aerator and the screen too, and if they still contain stains, you can soak the parts in vinegar for quite some time.

Reinstalling the aerator 

Once you are done, you may now want to reassemble the other parts of the aerator and then reinstall it into the end of the faucet spout.

You need to keep your aerator somewhere safe as you will need to return it after some time. This is because permanently removing your aerator is not wise at all.

When you remove it, you will also have an idea of how to replace it. Many individuals who have problems with the water flow always remove the aerator and fail to replace it, and they end up disposing of it.

Important Things to Note

You should know that a faucet aerator restricts the water flow rate from your faucet. Virtually all faucets have a similar rate of 2.2 gallons per minute. The faucets always have flow restrictions put in place to conserve water. Some people always change their aerators to reduce or increase the flow rate of water.

It is always recommended to try and clean your aerators and also do the replacement if the one you have get old.

Cleaning helps in removing dirt that may cause clogging or jam as it might block the flow. The faucet aerator doesn't need to be hand tight as you can gently do it. If it reaches a point of you needing to replace the aerator, you should some thorough research and buy only from Grohe supplies.

Also Read: ​How to Use Jack LaLanne Power Juicer: Easy Steps​​​

The aerator should match your kitchen faucet having in mind that the aerators differ.

Final thoughts 

Every kitchen faucet has its own unique aerator, and that's why you need to what your kitchen faucet aerator is. Some aerators have male threads, and some have female threads on them. It is evident removing the flow restrictor from your Grohe kitchen faucet is easy based on the article provided.

10 Simple Tips to Fix a Scratched Kitchen Cabinet

10 Simple Tips to Fix a Scratched Kitchen Cabinet

Cabinets are part of the modern kitchen, and they come in different shapes, sizes, and color. Some are made of wood, metal, glass, etc. Even though they are long-lasting, it is natural for them to breakdown. This depends on how you take care of your furniture. Kitchen cabinets may break down at some point, and that's pretty normal.

But what about when you step into your kitchen and then realize there's a scratch in your favorite cabinet? Maybe you might have accidentally scratched on it while cleaning the surface. Unfortunately, most of us become clueless on how this can be fixed.

May Like: ​How to Tighten Garbage Disposal Blades: Useful Tips​​​

So how do you fix a scratched kitchen cabinet? 

Fixing scratched cabinets is easier than you think. You don't need to make trips to the store when all you need is right in your kitchen. Some of these tips may make the scratch go away completely, while others will just help retouch them. Your scratched cabinets will look totally different from what it was before. The messy or rough surfaces on your cabinet won't be visible anymore.

Requirements & Steps to Fix

When fixing a scratched cabinet in your kitchen, you will need the following items: wood filler crayons, coffee, teabag, lemon, peanut butter, walnuts, iodine, etc.

1. Furniture marker and crayons

The simplest way you can use to repair the scratched surfaces is by using the furniture markers. No matter the color of your kitchen cabinet, you will find a matching color that bests suits it and hides the scratches.

  • Clean the surface 

First, clean the surface you want to work on. Take a damp paper towel and wipe the scratched area gently. Wiping ensures all dirt and dust are removed. Make sure it's dry before starting to fix the scratch.

  • Pick a color wax

Choose a color wax that matches the material of the cabinet and apply it gently on the scratched area. Start with a lighter color of the shade that matches your cabinet, then a color two shades lighter than the first color and blend. Finish off with a darker shade of the same color and blend for a few minutes with your fingers.

Wipe off any excess wax that might have spread around the surface of the scratched area. Let the wax on the scratched area dry for about 30 minutes and then buff it with a paper towel.

2. Vinegar and oil

Mix half cup vinegar with a half cup olive or cooking oil. Dip a synthetic material on the mixed solution. Rub firmly on the scratched part until it goes away. The oil will swell up the cracks on the scratched place while the work of the vinegar is to stain the wood.

3. Coffee

For brown cabinets, pour coffee grounds in a small bowl and add a little water. Grind them together to form a thick paste. Dip a ball of cotton wool or use a small rug into the mixture and apply it on the area that was scratched.

Wipe away the excess with a soft cloth after some minutes. Repeat this process several times until you get a darker finish. The grounded coffee paste will fill in the scratches of the cabinet.

4. Teabag

Turn your favorite beverage to a recipe for managing that scratched cabinet. Place a teabag in a cup and add hot water to it. Leave it for some time to darken enough. Put cotton swabs into the mixture and rub it over the scratched area. Wipe away any excess that may have spilled around the other parts. Leave it to dry

5. Mineral oil and pumice

Mix pumice powder with mineral oil to a fine smooth paste. Dip soft steel wool into the paste and rub it on the scratched area of the cabinet. Leave for some time for the paste to settle in the area and then wipe off with a damp paper towel. Buff with a dry paper towel thereafter.

5. Petroleum jelly

Apply petroleum jelly to the scratched area and leave it overnight for better results. Alternatively, use mayonnaise.

6. Lemon juice

Get a lemon and squeeze it to extract the juice, mix the lemon juice with olive oil, and apply over the scratched part of the cabinet. When applying the mixture, make sure you rub it in the direction of the scratch until it fades away.

7. Peanut butter

Spare some peanut butter from your kitchen and use it to remove those annoying scratches. Take some peanut butter and rub it over the scratch and then leave it for an hour for better results. Buff off with a dry paper towel for a smooth finish.

8. Walnuts

This one is pretty simple. To fix the scratches with a walnut, rub the walnut on the damaged surface. When you are done rubbing, buff it with a paper towel or a soft cloth. Crack the walnut and rub it on the surface, or you can use walnut oil as well. They will both work effectively.

9. Iodine

Take a cotton ball and add drops of iodine to it. The number of drops depends on the size of the scratched surface. It is suitable for dark wooden kitchen cabinets.

10. Paint

This works for tiny or small scratches. You can take a small amount of paint to cover up the area. Pick a color that is a shade darker for better results. Choose oil-based paint for use.

Important things to remember 

  • Take care of your cabinets and avoid ruining them intentionally or accidentally. Don't bang them, or use rough material that will scratch and ruin its beauty.
  • It is important you put a matching color to rub in the scratched areas to avoid messing it further.

May Like: ​How to Fix a Leaky Kitchen Faucet with Two Handles​​​

Conclusion

You can never run out of options when repairing a scratched cabinet. Most of them may be temporary and should go away if you use the above methods.

Scratches are so easy to handle that you won't even consider hiring a professional when you can do it yourself. Apart from trying to remove them, consider covering them up. Not all scratches require rubbing. Others need to be blended in to give the cabinet a new look it needs.

How to Fix a Leaky Kitchen Faucet with Two Handles

How to Fix a Leaky Kitchen Faucet with Two Handles

If you have a sink in your kitchen, chances are you have had trouble once in a while with dripping water from the faucet. Most modern kitchen sinks usually have two faucets handles. One faucet handle is for cold water while the other designed for hot water. When it is leaking, the first thing you should do is determine the sides that leaking.

A leaky faucet is one that drips water from the spout. Faucets leak when seals close or stop functioning properly. Seals are designed to open and close to allow water to flow properly through the faucet.

May Like: ​How to Use Jack LaLanne Power Juicer: Easy Steps​​​

But if they don't close efficiently, you are prone to having water drip from the tap. Leaking water may bring wastage and incur more water bills than usual, not forgetting the annoying sounds dripping water make in the sink. Who loves that?

How much does a leaky faucet costs per year?

Wasting water is irresponsible, and a leaking tap can waste millions of gallons in the long run. A leaky faucet easily represents a loss of 0.5 liters per hour, i.e., 12 liters per day and 4380 liters per year.

Below are some of the ways one can follow to repair any leakage from the faucet.

Requirements

To repair leakage in a faucet, you will need several basic tools. You don't want to start searching for forgotten tools up and down or run to the store in the middle of working. You will need:

  • Hex wrench
  • Adjustable screwdriver
  • Groove-joint pliers
  • Plumbers grease
  • Flat screwdriver
  • Utility knife

Steps to fixing the leakage

Before you start to disassemble to ascertain the cause of the leakage, it is essential to know which type of faucet you are trying to fix. Is it the cartridge type, compression, or ceramic?

Find the side that is leaking by turning off the water supply valves located under the sink to see where water is leaking from.

To begin with, turn off one faucet handle to see if it is leaking or not. Repeat the same to the other handle to see if there is leakage coming out of the faucet.

1. Fixing a leaking compression faucet

  • Turn off the water supply

Do this either by shutting off the fixture valves, turn in a clockwise motion. They are located below the sink. If there are no shut off fixtures, turn off the main water supply in your house.

To close the water flow in a compression faucet, tighten the handles down. Compression washer faucets are more likely to be prone to leakage though they are cheaper than cartridges.

  • Open the faucet to release the pressure

When the water supply is completely off, open the faucet to release pressure in the water. When any pressure has been released, cover the drain to avoid losing small parts of the disassembled faucet into the drain accidentally. Use a plug or damp cloth to cover the drain.

  • Find a water leak 

Locate the side that is leaking and work only on what's faulty. If all the sides are not working properly, then you can fix them together.

  • Remove the handles 

Remove the faucet handles. With the flathead screwdriver, unscrew them and then pull the handles.

Set a hex screw into the handle and hold it in place. Loosen the screw with an upward pull to lift the handle.

Faucets might be old, too, and therefore the handle might be hard to remove. Minerals can build up, thus hardening it. You can tap it gently with a hammer to loosen the bond. Use a utility knife to remove the decorative cup located at the top of the handle.

Also Read: ​How to Get Glass Out Of a Garbage Disposal: 3 Minute’s Job​​​

Keep the assembled parts aside in one place to avoid losing them accidentally.

  • Removing the cartridge 

When the handles have been successfully removed, remove the stem. To do this, pull it out of the faucet. If there is a nut that's making it uneasy to pull out, get a pipe wrench to remove the nut, and your cartridge will now be free for removal.

  • Replace worn out parts 

Check the condition of the rubber/neoprene seals that are located near the stem washer you've just removed if they are worn out or not. Replace damaged parts by getting duplicates from your local hardware.

If your cartridge does not need replacement, make sure you clean everything before putting them back. For clogged up dirt by minerals, soak it with vinegar and then use a nylon scrub pad to wipe off the surfaces for a cleaner and shinier look. Replace the O-rings that are on the cartridge if need be.

Lubricate them before fixing the replacements. Reassemble all the parts you removed, and its time to put them back. Grease the O-rings before putting them back. Clean the valve, both inside and outside. Replace the cartridge that was leaking.

Reverse what you did to fix them back, start with the step you finished with while repairing and finish off with the handles back in place. Test if the leakage is fixed. Open the valves that were switched off and turn on the faucet and turn off to see if it's still leaking. If leaking still persists, disassemble again to fix and consider replacing the valve with a new one. Get a new valve from the hardware and always carry the old one with you to help you in purchasing a similar size and type.

2. Fixing a cartridge leaking faucet

Cartridge faucets are so easy to fix and do not require a lot of work. Turn off the water supply to the faucet of both handles. Open the faucet to release water pressure. Use a screwdriver to unscrew the screws that are on the faucet handle and pull the handle.

Use a pipe wrench to remove the retaining nut and pliers to pull out the cartridge. Check if the O-rings are worn out if they are, then you need to replace the cartridge. Reassemble all the removed parts and put back the faucet handle to its place. Tighten back the set screw onto the handle. However, don’t tighten it too much.

  • Turn on the water supply 

Now that everything is finished turn on the water supply to test if the faucet is working. After turning on, turn off again to see whether there's leakage or it is completely fixed.

3. Ceramic disk faucet

To fix a leakage in a ceramic faucet, make sure you shut off the water supply.

Loosen the set screw using a hex wrench to be able to remove the faucet handle.

Remove the faucet handle by pulling it out using pliers to remove the retainer nut. Use a flathead screwdriver to remove the decorative caps located at the top of the faucet.

When you've removed the cap, the valve retaining nut will show. Loosen the cartridge with groove joint pliers and remove it. The cartridge can also be removed by hand. Use a screwdriver to remove the seals located at the bottom of the cartridge and clean them using a toothbrush.

Take a screwdriver and remove the O-ring from the faucet. Apply silicone grease to the O-ring with the tip of your fingers. Put the cartridge to the faucet body and use groove joint pliers to tighten it. Do not over-tighten to secure it.

Reattach the decorative cap using your hands and then put back the handle. Tighten the set screw with an Allen wrench. Turn back on both water supply lines and test your faucet if there is no leakage.

Conclusion

When unscrewing a valve seat, turn it counterclockwise. Leaky faucet brings so much wastage in water that you should not hesitate to fix it immediately. It will not only save you water but also from paying water bills of what is going at a waste. Repairing faucets is not hard at the comfort of your home with the right tools. There are so many things that cause leakage, but it all starts in the valve.

How to Use Jack LaLanne Power Juicer: Easy Steps

How to Use Jack LaLanne Power Juicer: Easy Steps

The majority of individuals have the habit of buying everything in the store, and this includes cooked food and drinks. Many think that it's too much work to do the work by themselves. When you walk to a store, the only thing you think of is buying everything that has been made easy for you to use.

Technology has advanced, and everywhere they sell everything that each and everyone wants. If you are a fun of drinks, especially ones that are made from fruits or vegetables, why don't you try making them at home? If you own a power juicer, then you can easily then you can make your juice and enjoy it in the comfort of your home.

May Like: ​How to Tighten Garbage Disposal Blades: Useful Tips​​​

What if I don't know how to use a power juicer? 

Some individuals have a power juicer at home, but they ignore using it because they are not sure how to operate it in the first place. They would rather buy packed juice from a store than use their Jack LaLanne power juicer.

A Jack LaLanne power juicer comes with a manual that contains instructions that are very simple to understand and put in practice. The instruction is highlighted in the booklet or a manual that can guide you. If you follow the instructions as indicated, you will enjoy your fresh juice at the comfort of your home. Read below on how to use a Jack LaLanne power juicer.

Assembling Your Jack LaLanne Power Juicer

You must ensure that all the parts are assembled correctly and in order. This you should do before using the power juicer. It is important to acknowledge that the upper part of your juicer is in the correct order. You can read your manual and do it the correct way. It has a receptacle that should be placed at the bottom then ensure you keep your filter based at the center of the receptacle.

The blade should be at the core of the filter, and at this point, make sure it is tightened well and then slightly turn it in a clockwise direction until its snug. Afterward, cover it using its lid and make sure it's locked nicely. If you are struggling to assemble it, make sure to read every process to understand. If you assemble inappropriately, your power juicer will not function, or you might end up damaging it. If you are sure it's fully assembled, connect your juicer to the power.

Making the Juice

  • If you have the fruits you wanted to make juice from, ensure you wash them nicely before you start using them. Make sure you peel your fruits before you insert them in the power juicer.
  • Place your jack LaLanne power juicer on a smooth surface where it can stand still. If you happen to place it in a slanted place, it can easily roll and break.
  • Take your piece of container that you want to put the juice in and place it under the spout and start by inserting the fruits inside the funnel as you direct them to be cut. You will guide them using a pusher, not your bare hands.
  • You do not want to risk getting injuries as a result of using your fingers. The Jack LaLanne power juicer comes with all its parts. Therefore, make sure you put all of them in use.
  • You should chop your fruits into smaller pieces so that they can easily go inside the funnel. Large pieces cannot fit the funnel, and that means they will not be crushed, or you might use a lot of energy trying to crush them.
  • You can now add water to help in the process, and that is in small quantity until it reaches your satisfaction.
  • You can make your juice using different types of fruits and even try a mix with vegetables to get a new taste or experience.

Congratulations! You've made yourself a homemade juice, and you can be sure it has healthy nutrients that will help your system. Once you are done, pour your juice into a cup and enjoy it.

Cleaning the Jack Lalanne Power Juicer

  • Before you start cleaning it, you first need to disconnect your juicer from the power and make sure you wash it.
  • When cleaning it, always pull out the pusher and the lower locking bar, then the lid and pulp collector.
  • Make sure to unscrew and gently pull out the blade. Do not rush removing the blade as it might cut you and cause severe injuries.
  • Once you've succeeded in pulling out the blade, you can also pull out the filter, followed by the receptacle.
  • You need to wash all these parts with clean water. The water needs to be warm enough to carry out your cleaning properly and remove any stain that could be left.
  • You can choose to dry them with a clean towel or place them in a rack where they can slowly dry.

Make sure you store your jack LaLanne power properly if not in use, and in that way, you will be able to use if for many years.

Using a jack LaLanne power juice is easy and not as hard as some people think. You can easily make your juice when you follow the instructions indicated in the manual. The booklet or manual has listed instructions that you can easily follow even when cleaning it.

The Jack LaLanne power juicer does not make any noise when in use. The motor operates quietly and durable, which means it can last for a long time compared to these other types.

Also Read: ​10 Simple Tips to Fix a Scratched Kitchen Cabinet​​​

The feeder is big and round, which will not pour your content out while using it. The blades are made of stainless steel; therefore, it doesn't attract rust. It is also fast, and you can have your juice within seconds of making it. When you compare jack LaLanne power juicer, it will extract up to 30 percent more juice than others.

Final thoughts 

You can use all types of fruits and vegetables in a Jack LaLanne power juicer. If you do not own a Jack LaLanne power juicer, make sure you include it in your next budget and make your fresh juice at the comfort of your home.

How to Tighten Garbage Disposal Blades: Useful Tips

How to Tighten Garbage Disposal Blades: Useful Tips

Garbage disposals work automatically while others are manually operated through the switch. It is a piece of important equipment in the kitchen installed under the sink that helps in the disposal of food wastes. Inside, there are two stainless steel blades inside for chopping the food pieces.

The electric motor inside the garbage disposal circularly rotates to shred food into small pieces. The small pieces pass through the pipes and drown to the drain.

May Like: ​How to Get Glass Out Of a Garbage Disposal: 3 Minute’s Job​​​

However, not all types of food can go through the garbage disposal. These include tough foods like bones, greasy foods, and so on. When these things go down the drain, they either clog up or make the blades loose with time.

Just like any other equipment, they go through a mechanical breakdown. What happens when the blades get loose at some point? Bolts holding the blades might get loose. Loose blades in the garbage disposal can make your sink emit a bad odor. The kitchen should smell nice and healthy.

Blades play an important role in the equipment. Without them, the garbage disposal won't shred anything. When the blades are loose, the garbage disposal removes unusual sound. The disposer won't grind easily with loose blades.

We bet you don't want the discomfort in your kitchen from the damage, fix it before it stops working completely.

Tools and materials you will need

When fixing something, you need to have tools at hand for better repair. Some of what you will need are:

  • Nut driver
  • Flashlight
  • Rug
  • Pipe wrench

Preparation

Before starting the process of fixing it, remember precautions comes first. Switch off power from the main power and the power source under the sink. Wear protective gloves and avoid working on wet hands. This way, you can avoid being electrocuted. Safety comes first. Get your tools ready.

How to fix

Step 1

Switch off the electrical socket located below the sink. Unplug the garbage disposal from the wall and ensure there's no electrical connection to avoid your hands being shocked.

Step 2​

Put a bucket underneath to trap water that may drip while you are fixing it. Put your hands and feel the movement of the blades. They should be moving horizontally, side to side on the rivets.

If you notice they are moving vertically, that means they are loose. Sometimes its clogged food that can make your blades feel loose and stop working properly. Check for clogged food waste or foreign objects like glass that may be stuck there.

Check if the impeller plates are moving to ascertain if something is clogged or not. You can use your hands to remove the clogs. But for a more effective way, use nose pliers. Alternatively, use the end of a broom, tongs, or wooden spoon to push the dirt out. Make sure there's good lighting while working. Plug in and turn the water on and test if it is grinding correctly.

Step 3​

Make sure the drain line is disconnected. Unscrew the nut that holds the drainpipe to the disposal garbage. Be careful and unplug the unit gently, not to accidentally drop it on your legs. It might injure you or ruin your kitchen floor. To unscrew, use a pipe wrench to loosen the nuts easily.

Locate the loose blades and check to be sure nothing is stuck there. The blades have impellers which are not usually sharp as you may think but are blunt. Tighten the two bolts holding the blades with a night driver. You can use a flashlight.

Don't tighten the bolt so tight that to damage the threads but tight enough to function properly. If the blades are old, replace them with new ones. Consider replacing them with stainless blades. Also, if the blades are damaged or worn out, replace them with new ones. Put the blades in the same position they were in for the garbage disposal to function smoothly and are aligned correctly.

Step 4

When all the bolts are tight enough, it's time to clean. Bolts can be tightened by hands and then a little after with pliers. Cleaning is very easy and does not take much time. All you need is a rag to clean the sink to remove any dust and dirt. Wipe off the dirt around gently.

Step 5

Reconnect the garbage disposal to the sink. Use a pipe wrench and screw it back in place. Search for any visible damages like cracks on the surface of the unit or leaks. Do this by filling the sink with water and checking the drainage. Use cold water instead. Switch on the circuit breaker and plug to start it.

When everything has been put back in place, check if your garbage is now working efficiently. There should be no unusual sound. Garbage disposals make noise when working, but it should not be screeching. If everything works fine, then that means your blades are not loose anymore.

Conclusion

Garbage disposal is important equipment in your kitchen, and every day we have garbage to throw away, make sure you use it correctly. Don't grind food wastes that are tough to protect your blades. Avoid foreign objects like glass or any cutlery from going down the drain accidentally. Knowing what goes in and what does not need to.

When unclogging your garbage disposal, its recommended to use cold water and not cold one if greasy foods are stuck inside. Cold water will solidify and makes it easier when you open the disposal to clean the blades. Hot water might push clogs further and make it difficult to remove.

Don't wait until it is damaged to take precautions. Regular maintenance keeps it working efficiently for an extended period of time. Put ice blocks once in a while inside the garbage disposal to sharpen the blades. These tips should help you fix your plumbing problems with garbage disposals. They are easy to follow and requires little skill to get you going. If you still find trouble with your garbage disposal, find a professional plumber to help you with tightening the blades. Don't let small things put you in another budget in what you can fix early.

How to Get Glass Out Of a Garbage Disposal: 3 Minute’s Job

How to Get Glass Out Of a Garbage Disposal: 3 Minute's Job

Nearly all kitchen sinks are built with garbage disposal mounted on the lower side of the sink as it helps in collecting solid food. Every household depends on the garbage disposal to help them in the intake of leftovers. It's a great appliance that is appreciated in every kitchen in a home.

As much as garbage disposal can help to take the unwanted food materials, many tend to confuse it with a garbage can. This is because people dispose of any food on the garbage disposal, thus damaging it.

It is always essential to take note of what foods should be taken to the trash and what the garbage disposal is meant for. When you correctly use your garbage disposal, you will prevent clogs and disposal jams from occurring.

May Like: ​How to Fix a Broken Kitchen Drawer: Let’s Go for It​​​

Things like potato peels, bones or any hard objects should not go through the garbage disposal. Many who pour hard objects like bones always believe that garbage disposal has sharp blades that can cut through hard materials. That is not true at all and having that in mind you should throw garbage to where it belongs.

What if you are washing and glass breaks into pieces and makes their way to your garbage disposal? How will you go about removing it?

You need to get out this glass very carefully to avoid getting any cuts. Read here to learn how to get a glass out of garbage disposal.

Requirements

There are some tools you will need to be able to get out of the glass. This includes:

  • A vacuum
  • A pair of pliers
  • A broom or a hammer

You should never do the removal with your bare hands as it's very dangerous. You will also need a garbage disposal manual in the case where you need to remove the garbage disposal from where it is fixed.

Make sure you have all these tools before you start the process of getting out the glass.

Using a Pair of Pliers

Before you start removing the glass, you need to ensure that the power being supplied to the garbage disposal is off.

You can choose to turn off the power on the disposal only. But to be on the safer side, disconnect the power at the power source or circuit breaker. This is to avoid any serious injuries resulting from being electrocuted.

Avoid sticking your hand into the drain, hoping that you will pull out the glass. You will only come out with several cuts or bruises from the glass or have your hand stuck in. Make sure you have a pair of pliers to get out the glass or if it's broken, you can use it to remove the large pieces.

Pull out as many pieces as you can because you are likely to get hold of the bigger pieces at the top of the drainage.

You need to do this process repeatedly until you feel that there are any bigger pieces left. If you are unable to get out of the glass, you can start by dislodging it first.

You can use your broom by inserting its handle on the top of the garbage disposal and then wiggle it to dislodge it. After dislodging it, you can use your pair of pliers to remove all pieces you can reach.

Vacuum To Remove the Glass

Here you will need to vacuum the garbage disposal, and you will successfully do this using a wet-dry vacuum. Suck out the glass from the drain opening using the long head attachment of the vacuum. You will repeat this process until you are unable to see anything being sucked up.

Remember that some pieces will need to be sucked one by one and this is in the case where the nozzle is not wide.

If you have a double sink, then make sure you cover up the holes to maximize the suction on the dispenser. You can also turn the blades to remove the last bits of pieces of remaining glass.

Turn on the blades of the disposal using your broom handle, and then suck the remaining glass using the vacuum.

Once you are finished, you can clean the vacuum. At this point, you will need to rest your garbage disposal, and that is by powering on the power source.

Run your tap to wash away any small pieces that might be left behind. If the garbage disposal still cogs or jams, that will mean that there is a piece of galls still left.

May Like: ​How to Use Jack LaLanne Power Juicer: Easy Steps​​​

You will switch off the power and repeat the process until you get out of the glass. The process is easy but very dangerous. And that means a total concentration is important.

You can also choose to remove the garbage disposal from the sink following the instruction on the manual. Garbage disposal is known to be heavy and getting the help of a friend, or family member is necessary.

After removing the garbage disposal, carefully remove the piece of glass out, then reinstall it back according to the manual.

Thinks You Should Know

When installing back your garbage disposal, make sure you follow every detail in the manual. If you miss something, you might end up damaging your garbage disposal.

The glass is a hard object that cannot be cut into smaller pieces. If a glass goes down the drainage, never assume that it has been broken into smaller pieces; thus, it can cause any harm.

It is dangerous, and if you continue using your sink without sorting out the issue, it will lead to clogging or jamming. You do not need to buy a new unit altogether as you can simply fix the problem. If you experience a jam or clogs in your sink, locate where the problem is.

Verdict

If your child was doing some washing and end up dropping a glass, they might not tell you. Therefore, it is important if you teach them that when something like that occurs. It is also important they let an adult know before they can go on using it. Make it clear that it might cost you a lot of it goes unnoticed.

How to Fix a Broken Kitchen Drawer: Let’s Go for It

How to Fix a Broken Kitchen Drawer: Let's Go for It

The majority of people always build their houses in different styles and designs. Many tend to include drawers in various rooms like the bedroom or kitchen. This they use to store their different items, perhaps in an orderly manner. Drawers have many uses, and one can store utensils, foodstuffs like cereals, and even household items they are not using. This helps present the kitchen neatly and nicely arranged. A kitchen drawer is important in every household as they help out, but it's surprising to know that the drawer gets abused a lot. For instance, you open a drawer and fail to close it. Someone else might come and bang it to its place with the idea of closing it.

Kids also have a habit of swinging on the handles, thus making them weak. It's also a habit of always overloading them now and then, which makes them more fragile. Your kitchen drawer might withstand all this abuse, and when the time comes, it will break down. The side will separate, the knobs will become loose, and the guides might also wear out.

May Like: ​How to Clean a Kitchen Stainless Steel Sink: 3 Facts​​​

When that happens, many will always prefer to replace the drawer with a new one stating that it's not of good quality, yet they forget the way they mishandled it. If your kitchen drawer is broken then you need to repair it so that it continues serving you properly. The article below will discuss how to fix a broken kitchen drawer following these simple techniques.

Tools You Require

When fixing your broken kitchen drawer, you need to have some tools to help you in the repair. The various tools you need are a putty knife, brush, drill, wood glue, and clamps, among others.

You need to make sure you have all the requirements before you start your repair. Gloves and safety eyeglasses are also a bonus if you have.

You will be handling different tools, and you need to be careful so that you avoid getting injured. Fixing a broken kitchen drawer is simple by following the following steps.

Fixing the Drawer Boxes

When fixing the drawer boxes, you will have to take the drawer from the chest, and that is by pulling it outside.

Tilt your drawer from the upper side until it loosens the guides, and then place it in a flat or smooth surface.

You will have to remove the screws from the drawer by unscrewing them to be able to remove the solid front of the drawer.

You can use a drill or a screwdriver to pull out the screws. Afterward, insert a drill that measures 3 to 16 inches in the screwdriver all the drill you are using.

Make other holes and base them at the front drawer box next to the previous holes. Use your brush to clean all the dirt inside the drawer and make sure it's thoroughly clean.

Insert the putty knife in any available separations, or the loose joints then disassemble the joints.

Apply the wood glue in the cracked or separated parts and clasp them in order to make them stronger.

You can give it time by allowing the glue applied to dry off and then pull out the clamps. If you need to add strength to the box, then it's appropriate to apply hot-melt adhesives around the drawer and allow it to dry.

You can finalize by making sure you screw the upper front to the box with the help of the current holes you made and the initial screws.

Fixing the Drawer Guides

Once you have detached the drawer from its closet, take a flat blade to help you detach the drawer slides from its chest.

You need to buy a new one, so you have to check the old one to know the manufacturer. Make sure the guides you buy are similar from length to width.

Start by taking the slides out from the parcel and read how they are made to fit. You will notice that they have been marked according to their specific place to be fixed.

Get rid of the old slide and exchange it with a new slide with the help of flat blades that come with the slides.

When installing the guides, it will be easy if you make a comparison of the initial screws' holes in the chest. You need to be keen when carrying out this to avoid mixing or confusing yourself.

You will repeat the same process for the opposite side once you are done with the right and also the bottom part.

Make sure you check the labeling correctly to avoid screwing them on the wrong sides. You do not need double work or spending more money to buy other parts.

Your kitchen drawer that was broken is now completely fixed, and it's your responsibility to take care of it properly.

As you can see, the process of fixing your broken kitchen drawer is easy and consumes a little time if you follow the instructions as indicated. This is something that you can do by yourself, which means you do not need any skills or a professional to repair for you. Hiring a professional to repair for you is much expensive compared to when you do the fixing work yourself.

All you require is the right tools and following the instructions as written to guide you through. In no time, you will have fixed your kitchen drawer properly and have it back to its original condition.

Essential things to keep in mind 

It is vital to put on safety glasses and gloves when working as you will be handling the screwdrivers with your hand. If you do it with your bare hands, you might get bruises or cuts. The safety glasses protect you from getting a small particle from entering your eyes while screwing holes. These protective gears help you achieve your work without getting any injury.

Final thoughts 

Always handle your drawers properly and make sure you do not overload it or even slam it. That kind of behavior is what weakens your kitchen drawer and you do not need to always fix it if it's correctly taken care of. Make sure you fix your broken kitchen drawer using those simple techniques.

How to Clean a Kitchen Stainless Steel Sink: 3 Facts

How to Clean a Kitchen Stainless Steel Sink: 3 Facts

Sinks play an essential role in our kitchen when cleaning utensils. For example, we clean our dishes, wash vegetables, and pour dirty water in our kitchen sinks. However, most of us do the dishes and then clean the visible parts of the tub.

Sometimes we just rinse with soap and water, but dirt builds up with time. We focus so much on the surface but don't pay attention to other parts such as the faucets. When cleaning, put three things in mind: scrub, sanitize, and disinfect.

Water alone cannot give you an effective cleaning. You'll need to go a step further for better results.

May Like: ​4 Easy Steps to Tighten a Loose Moen Single Hand Kitchen Faucet​​​

Things You Need To Clean Sink

  • Water
  • Soap
  • Sponge
  • Baking soda
  • Lemon juice
  • Vinegar
  • Lemon/orange peels

Before starting the cleaning process, declutter everything from the sink – from utensils to any food particles. Start cleaning from the faucet and handles and finish with the basin. This will save you time cleaning. Here are easy ways to keep your kitchen sink sparkling clean.

1. Faucets and Handles

For more effective and time-saving cleaning, start from the faucets and handles going down to the drainage area. Dip a soft sponge in warm water and then rub the faucet and the handles gently.

Use warm soapy water when cleaning the handles and the faucet. But use a small brush to remove dirt from areas that are not visible. There are small things we ignore cleaning like the faucet aerator if attached to the faucet. If you don't have a small brush, use a toothbrush instead.

Rinse with warm water. Take a solution of vinegar and soapy water for your final rinse to leave it cleaner. To remove tough discolorations around the faucet, put some cotton balls on vinegar.

Put the softened cotton balls with vinegar around the faucet. Leave them for 15 minutes before removing them.When everything is clean to your satisfaction, wipe them off with a damp paper towel and dry them with a dry cloth.

2. Sink Basin

This part is the most essential as it holds water. Soap and water alone cannot give your sink the shine it needs. You don't need expensive cleaning products to make your sink clean. They are available right in your kitchen.

Think of those lemon and orange peels that you throw away. The vinegar you use for cooking and the baking powder that spices up your baking? Those are what we are talking about. You have no excuse to complain of a dirty sink anymore.

As aforementioned, this part of your sink handles a lot of dirt, from piled up utensils to food leftovers. Declutter everything from the sink before cleaning. Use warm soapy water and a sponge. Then rub gently. Make sure to start cleaning from the sides as you move to the base of the sink. Continue rubbing in circular options until it's clean. Then rinse with water.

Disinfect the Sink 

We often forget to disinfect our sinks after cleaning it with soap and water. There are many ways to disinfect your sink.

You can use disinfectants you bought from the store or use these home remedies that are available in your kitchen. They not only freshens your sink but also help remove those stubborn stains.

Baking Soda

Sprinkle a fair amount of baking soda on the surface of your sink and rub with a sponge. Mix it with little water to make a thick paste and rub it on the sink with the sponge. This helps to remove stains and residue left after cleaning with soap and water.

Lemon or Orange Peels

Make use of the peels you do throw away, they are cleaning agents. Simply scrub the surface of the skin with the outer skin of the pill. Alternatively, cut a lemon into half, sprinkle salt on it or baking soda and use it to scrub. You can also extract lemon juice as an option.

Vinegar

Mix a small portion of white vinegar with water and rinse your sink with. Baking soda and vinegar can also work, too; use the ratio of 1:2 for better results.

3. Sink Drain

Your sink can never be clean enough if you don't consider this part. A clean drainage makes a clean sink. You've cleaned your sink, but what about the leftover food, grease, or soap stuck in the drainage? Don't wait for your sink to be clogged. Don't wait for the water to stop flowing before you clean down there.

Pour in hot water and use a plunger to suck the remains that might have been left there accidentally. Alternatively, pour baking soda into the drain, add vinegar, and wait for a few minutes.

Don't get scared if there's a bubbly reaction; this only happens for a short while. Rinse off with hot water to get rid of any residue left.

What More You Should Keep in Your Mind? 

Make cleaning a habit to avoid unnecessary odor from your sink. When cleaning the sink, also remember to clean the flat surface around the sink. We all love a good, clean kitchen that's odorless.

Use home or store-bought cleaner; choose what works perfectly for you. Don't keep dirty dishes in the sink too long when you are in a position to wash them right away. Put a trap in the drain to prevent left over foods from passing through and building up to clog your sink. To prevent clogging issues from grease, use a liquid detergent.

Wash your dish sponge with warm soapy water regularly to remove dirt and built-up grease. Bacteria can also build-up on the sponge, and it's good to change it frequently.

Rinse your sink with warm water and the drainage with hot water any time after washing the dishes. Sanitize your sink after cleaning. You can use natural kitchen sink sanitizes or store-bought ones.

May Love: ​How to Use Jack LaLanne Power Juicer: Easy Steps​​​

Final Thought

They work the same way. If a garbage disposal is connected to your sink, ensure its also clean and the drainage working properly. You don't want food wastes clogging up your sink and ruining your cleaned sink.

With those tips, you can make a difference in your kitchen.